Harken Rollpin replacement kit Bedienungsanleitung
Stöbern Sie online oder laden Sie Bedienungsanleitung nach Hardware Harken Rollpin replacement kit herunter. Harken Rollpin replacement kit User Manual Benutzerhandbuch
- Seite / 2
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
INSTRUCTION SHEET
Jib Reefing & Furling
Rollpin Replacement Kit
1251 East Wisconsin Avenue • Pewaukee, WI 53072 U.S.A.
Telephone: (262) 691-3320 • Fax: (262) 691-3008
Web: http://www.harken.com • E-mail: [email protected]
Rollpins Paper Towels
Loctite
®
277 (Red) Hammer
Wood Support Block Center Punch
Flushing Punch Vice-Grip-type pliers
Loctite
®
Primer “N” (HFG395) Rollpin Punch (available from Sears:
3
/32” for #1,
1
/8" for #2)
Supplies Included Supplies You Need
Checking Joints
1. Take headstay down and remove lower drum assembly and feeder.
2. Recess threaded stud into bottom foil to allow room on wire to take
joints apart for re-gluing. If you have a Norseman
®
, Sta-lok
®
or Navtec
®
terminal, take bottom joint apart as directed below to allow space on
wire to separate foils.
3. Support joint area in the Wood Support Block (included). Use a Roll
Pin Punch to drive pin out or pound new rollpin half-way into foil, to
push old pin out half-way.
4. Pull both pins out of foil using vice-grips or pliers.
5. Try pulling foil sections apart. If they come apart, foils need
to be re-glued to connectors.
Continued
INSTRUCTION SHEET
Jib Reefing & Furling
Rollpin Replacement Kit
1251 East Wisconsin Avenue • Pewaukee, WI 53072 U.S.A.
Telephone: (262) 691-3320 • Fax: (262) 691-3008
Web: http://www.harken.com • E-mail: [email protected]
Rollpins Paper Towels
Loctite
®
277 (Red) Hammer
Wood Support Block Center Punch
Flushing Punch Vice-Grip-type pliers
Loctite
®
Primer “N” (HFG395) Rollpin Punch (available from Sears:
3
/32” for #1,
1
/8" for #2)
Supplies Included Supplies You Need
Checking Joints
1. Take headstay down and remove lower drum assembly and feeder.
2. Recess threaded stud into bottom foil to allow room on wire to take
joints apart for re-gluing. If you have a Norseman
®
, Sta-lok
®
or Navtec
®
terminal, take bottom joint apart as directed below to allow space on
wire to separate foils.
3. Support joint area in the Wood Support Block (included). Use a Roll
Pin Punch to drive pin out or pound new rollpin half-way into foil, to
push old pin out half-way.
4. Pull both pins out of foil using vice-grips or pliers.
5. Try pulling foil sections apart. If they come apart, foils need
to be re-glued to connectors.
Continued
INSTRUCTION SHEET
Jib Reefing & Furling
Rollpin Replacement Kit
1251 East Wisconsin Avenue • Pewaukee, WI 53072 U.S.A.
Telephone: (262) 691-3320 • Fax: (262) 691-3008
Web: http://www.harken.com • E-mail: [email protected]
Rollpins Paper Towels
Loctite
®
277 (Red) Hammer
Wood Support Block Center Punch
Flushing Punch Vice-Grip-type pliers
Loctite
®
Primer “N” (HFG395) Rollpin Punch (available from Sears:
3
/32” for #1,
1
/8" for #2)
Supplies Included Supplies You Need
Checking Joints
1. Take headstay down and remove lower drum assembly and feeder.
2. Recess threaded stud into bottom foil to allow room on wire to take
joints apart for re-gluing. If you have a Norseman
®
, Sta-lok
®
or Navtec
®
terminal, take bottom joint apart as directed below to allow space on
wire to separate foils.
3. Support joint area in the Wood Support Block (included). Use a Roll
Pin Punch to drive pin out or pound new rollpin half-way into foil, to
push old pin out half-way.
4. Pull both pins out of foil using vice-grips or pliers.
5. Try pulling foil sections apart. If they come apart, foils need
to be re-glued to connectors.
Continued
INSTRUCTION SHEET
Jib Reefing & Furling
Rollpin Replacement Kit
1251 East Wisconsin Avenue • Pewaukee, WI 53072 U.S.A.
Telephone: (262) 691-3320 • Fax: (262) 691-3008
Web: http://www.harken.com • E-mail: [email protected]
Rollpins Paper Towels
Loctite
®
277 (Red) Hammer
Wood Support Block Center Punch
Flushing Punch Vice-Grip-type pliers
Loctite
®
Primer “N” (HFG395) Rollpin Punch (available from Sears:
3
/32” for #1,
1
/8" for #2)
Supplies Included Supplies You Need
Checking Joints
1. Take headstay down and remove lower drum assembly and feeder.
2. Recess threaded stud into bottom foil to allow room on wire to take
joints apart for re-gluing. If you have a Norseman
®
, Sta-lok
®
or Navtec
®
terminal, take bottom joint apart as directed below to allow space on
wire to separate foils.
3. Support joint area in the Wood Support Block (included). Use a Roll
Pin Punch to drive pin out or pound new rollpin half-way into foil, to
push old pin out half-way.
4. Pull both pins out of foil using vice-grips or pliers.
5. Try pulling foil sections apart. If they come apart, foils need
to be re-glued to connectors.
Continued
1
2
Inhaltsverzeichnis
Seite 1
INSTRUCTION SHEETJib Reefing & Furling Rollpin Replacement Kit1251 East Wisconsin Avenue • Pewaukee, WI 53072 U.S.A.Telephone: (262) 691-3320 • Fa
Seite 2
Printed in USA. 4884/2-05Gluing JointsIf furling system has been stored in a horizontal position, make sure inside of foils are dry. If they are wet,
Verwandte Produkte und Handbücher für Hardware Harken Rollpin replacement kit
(18 Seiten)
(8 Seiten)
(8 Seiten)
(8 Seiten)
(8 Seiten)Samsung DVD-V7575 podręczniki
Instrukcje obsługi i podręczniki użytkownika dla Odtwarzacze DVD Samsung DVD-V7575.
Dostarczamy 2 pdf podręczników Samsung DVD-V7575 do pobrania za darmo według typów dokumentów: Instrukcja Użytkownika
Kommentare zu diesen Handbüchern